Bell System Memorial

 

About Porticus Porticus Home Page References & Links Testimonials & Member Site Disclaimer
 
 Bell Labs Science Kits (Energy From The Sun)
 
Home Page About This Site What's New References and Links Bell System History Life in the Bell System Capsule History of the Bell System Bell Canada Bell Operating Companies Bell Labs AT&T Long Lines AT&T Historical Financials Historical Photos Historical Film & Video Bell Telephone Magazine Articles What Killed Ma Bell "The Day the Bell System Died The Rape of Ma Bell AT&T Divestiture The Decision to Divest Odds & Ends The Eastland Disaster Bell System Employee Stories Bell System Property - (Not) For Sale Bell Logo History Trading Post - Bell System stuff wanted, for sale, for trade, etc. Bell System Advertisements Don Lively's Essay and More Miscellaneous Retirees Info Trademarks and Copyrights Visitors Comments Dew (Distant Early Warning) Line Project "Yellow Pages" Site Map The Western Electric Store Books Bell System Practices (BSP) & Technical Manuals

Energy From The Sun

 


Photo 1


Photo 2


Photo 3


Photo 4


Photo 5

Note the three white "sheets" of asbestos in the top half of the picture above.  At the time these kits were produced, the hazards of asbestos weren't known.

Photo 1 shows kit with outer sleeve removed.  Photo 2 shows the arrangement of the box contents.  Photo 3 shows an overall view of the actual contents of the kit.  Photo 4 show a close up of the three asbestos sheets and the polishing plate.  Photo 5 shows a close up of the remaining parts.  Note the heater element and just to the left of it is a plastic tray.  The heater  element was not included in some of the kits I've run across.  There was a piece of paper with a notice about ordering the heater in the kits not having the heater.  It is still being made today and is available for purchase from Cooper Wiring.

 

Make your own solar cell from raw materials!  That is what you can do if you have this kit.  This kit is not for the technically or dexterity challenged as you will be working with several toxic chemicals, asbestos, red-hot heating element and a very fragile thin raw wafer of silicon.  For more information on photovoltaics (a.k.a., "solar battery", "solar cell", "solar panel"), see my web page dedicated to this subject by clicking HERE.

 

Chemical vials are in the lower right corner of photo 5.  A thin and fragile piece of silicon is protected (and hidden from view) by a piece of cardboard shown in the lower left corner of photo 5.  As with most other thumbnail images on these web pages, clicking on one of the images above will display the full- size image.

 

We Offer Personalized One-On-One Service!

Call Us Today at (651) 787-DIAL (3425)

The Western Electric Store

 

A website visitor in Sweden contacted us about this kit and told about his work on new photovoltaic technology at the  Ångström Solar Center (ÅSC), the photovoltaics research team at Uppsala University.

 

Based on an experiment shown in the manual for this Bell Labs Science Kit, he built a solar powered motor using scrap solar cell pieces and send the photos of his little motor.  His description and photos of the motor follows:

"The rotor is about two inches high, the coils have a height of about one inch and are made up of 250 rounds of 0.1mm (AWG 38) enameled copper wire each. They measure about 30 ohms each, which is accidentally close to optimum performance with the .5 cm2 thin-film Cu(In,Ga)Se2 solar cell which is mounted in the center of each coil. These cells (they are poor, waste from our lab) give about 400mV at 8mA under full illumination (about 5% efficiency).

In the pictures the lamp is to the right and the small round thing in the upper alligator clamp is a neodymium permanent magnet. There is an angle of about 30 degrees between the incident light and the magnet, seen from the axis of rotation.

The body of the rotor is a 5mm diameter glass tube which I sealed on one side with a blow torch, forming a point. The coils and solar cells are glued onto the body with epoxy. After fixating the cells and coils, I soldered the thin wire onto the contact pads of the solar cells - each cell is only connected to its surrounding coil, all wound in the same direction.

The axis is an unwound, straightened safety pin - the longest needle I could find" - Uwe Zimmermann, PhD

Thin Film Solar Cell Group
Solid State Electronics
The Ångström Laboratory
Uppsala University
Box 534
SE-751 21 Uppsala, SWEDEN http://www.asc.angstrom.uu.se/tsc/tsc.htm

Here are the photos Uwe sent of his solar motor experiment. Click on images below to view full size.:


Motor spinning - 1


Motor spinning - 2


Motor stopped


Close-up of solar cell


Motor components
separated - 1

Motor components
separated - 2

 


>>>> UWE'S SECOND SOLAR MOTOR - Mark 2 <<<<

Uwe constructed a "new and improved" solar motor and sent me a video of it running in his window from the sunlight.  He describes his second motor as follows:

"The main difference between the first design and "mark 2" is the use of paper bobbins for the coils and internally mounted permanent magnets on the needle - inside the rotor. The magnets are glued to the needle with epoxy resin, as are the coils and solar cells to the glass tube itself.

The coils themselves are 500 turns of 0.1mm diameter (AWG 38) copper wire on a 5mm diameter paper bobbin. This gives about 30 ohms of resistance, which again is an almost optimum match to the used solar cells.

The rotor is a glass tube with about 10mm diameter and 5cm height. The top is drawn out to a point after heating the glass tube with a blow torch. It's a bit off-center, hence the rotor tends to sway as it comes up in speed."

CLICK HERE TO VIEW VIDEO OF MOTOR IN ACTION!
 

 

This kit came with a book of almost 100 pages of kit instructions, historical background on Solar Energy, the part that Bell Labs played in the commercialization of silicon solar cells  and the physics of solar to electric conversion explained.

Sample pages from PDF File:
1  2  3  4  5  6  7  8

 

 

Contact Beatrice  Careers  About Us  Site Map  Disclaimer  Legal Policy  Privacy Policy

Copyright ©MDCCCXCIV-MMXV Beatrice Companies, Inc., All rights reserved.

Porticus Home Page